© by Tony van
555 timer IC was first introduced arround 1971 by the Signetics Corporation as
the SE555/NE555 and was called "The IC Time Machine" and was also the
very first and only commercial timer ic available. It provided circuit designers
and hobby tinkerers with a relatively cheap, stable, and user-friendly
integrated circuit for both monostable and astable applications. Since this
device was first made commercially available, a myrad of novel and unique
circuits have been developed and presented in several trade, professional, and
hobby publications. The past ten years some manufacturers stopped making these
timers because of competition or other reasons. Yet other companies, like NTE (a
subdivision of Philips) picked up where some left
primer is about this fantastic timer which is after 30 years still very popular
and used in many schematics. Although these days the CMOS version of this IC,
like the Motorola MC1455, is mostly used, the regular type is still available,
however there have been many improvements and variations in the circuitry. But
all types are pin-for-pin plug compatible. Myself, every time I see this 555
timer used in advanced and high-tech electronic circuits, I'm amazed. It is just
In this tutorial I will show you what exactly the 555 timer is and
how to properly use it by itself or in combination with other solid state
devices without the requirement of an engineering degree. This timer uses a maze
of transistors, diodes and resistors and for this complex reason I will use a
more simplified (but accurate) block diagram to explain the internal
organizations of the 555. So, lets start slowly and build it up from
The first type-number, in Table 1 on the left,
represents the type which was/is preferred for military applications which have
somewhat improved electrical and thermal characteristics over their commercial
counterparts, but also a bit more expensive, and usually metal-can or ceramic
casing. This is analogous to the 5400/7400 series convention for TTL integrated
in fig. 1 and fig. 2 above, come in two packages, either the round metal-can
called the 'T' package or the more familiar 8-pin DIP 'V' package. About
20-years ago the metal-can type was pretty much the standard (SE/NE types). The
556 timer is a dual 555 version and comes in a 14-pin DIP package, the 558 is a
quad version with four 555's also in a 14 pin DIP case.
the 555 timer, at fig. 3, are the equivalent of over 20 transistors, 15
resistors, and 2 diodes, depending of the manufacturer. The equivalent circuit,
in block diagram, providing the functions of control, triggering, level sensing
or comparison, discharge, and power output. Some of the more attractive features
of the 555 timer are: Supply voltage between 4.5 and 18 volt, supply current 3
to 6 mA, and a Rise/Fall time of 100 nSec. It can also withstand quite a bit of
The Threshold current determine the maximum value of Ra +
Rb. For 15 volt operation the maximum total resistance for R (Ra +Rb) is
The supply current, when the output is 'high', is typically 1
milli-amp (mA) or less. The initial monostable timing accuracy is typically
within 1% of its calculated value, and exhibits negligble (0.1%/V) drift with
supply voltage. Thus longterm supply variations can be ignored, and the
temperature variation is only 50ppm/°C (0.005%/°C).
timers rely upon an external capacitor to determine the off-on time intervals of
the output pulses. As you recall from your study of basic electronics, it takes
a finite period of time for a capacitor (C) to charge or discharge through a
resistor (R). Those times are clearly defined and can be calculated given the
values of resistance and capacitance.
The basic RC charging circuit is shown in fig. 4. Assume that the
capacitor is initially discharged. When the switch is closed, the capacitor
begins to charge through the resistor. The voltage across the capacitor rises
from zero up to the value of the applied DC voltage. The charge curve for the
circuit is shown in fig. 6. The time that it takes for the capacitor to charge
to 63.7% of the applied voltage is known as the time constant (t). That time can
be calculated with the simple expression:
t = R X C
resistor value of 1 MegaOhm and a capacitor value of 1uF (micro-Farad). The time
constant in that case is:
t = 1,000,000 X 0.000001 = 1
Assume further that the applied voltage is 6 volts.
That means that it will take one time constant for the voltage across the
capacitor to reach 63.2% of the applied voltage. Therefore, the capacitor
charges to approximately 3.8 volts in one second.
Fig. 4-1, Change in the input pulse frequency allows completion of the
timing cycle. As a general rule, the monostable 'ON' time is set approximately
1/3 longer than the expected time between triggering pulses. Such a circuit is
also known as a 'Missing Pulse Detector'.
at the curve in fig. 6. you can see that it takes approximately 5 complete time
constants for the capacitor to charge to amost the applied voltage. It would
take about 5 seconds for the voltage on the capacitor to rise to approximately
the full 6-volts.
Definition of Pin
Refer to the internal 555 schematic of Fig.
(Ground): The ground (or common) pin is the most-negative
supply potential of the device, which is normally connected to circuit common
when operated from positive supply voltages.
Pin 2 (Trigger): This pin is the input to the
lower comparator and is used to set the latch, which in turn causes the output
to go high. This is the beginning of the timing sequence in monostable
operation. Triggering is accomplished by taking the pin from above to below a
voltage level of 1/3 V+ (or, in general, one-half the voltage appearing at pin
5). The action of the trigger input is level-sensitive, allowing slow
rate-of-change waveforms, as well as pulses, to be used as trigger
One precaution that should be observed with the trigger input signal
is that it must not remain lower than 1/3 V+ for a period of time longer
than the timing cycle. If this is allowed to happen, the timer will retrigger
itself upon termination of the first output pulse. Thus, when the timer is
driven in the monostable mode with input pulses longer than the desired output
pulse width, the input trigger should effectively be shortened by
The minimum-allowable pulse width for triggering is somewhat
dependent upon pulse level, but in general if it is greater than the 1uS
(micro-Second), triggering will be reliable.
A second precaution with respect
to the trigger input concerns storage time in the lower comparator. This portion
of the circuit can exhibit normal turn-off delays of several microseconds after
triggering; that is, the latch can still have a trigger input for this period of
time after the trigger pulse. In practice, this means the minimum
monostable output pulse width should be in the order of 10uS to prevent possible
double triggering due to this effect.
The voltage range that can safely be
applied to the trigger pin is between V+ and ground. A dc current, termed the
trigger current, must also flow from this terminal into the external
circuit. This current is typically 500nA (nano-amp) and will define the upper
limit of resistance allowable from pin 2 to ground. For an astable configuration
operating at V+ = 5 volts, this resistance is 3 Mega-ohm; it can be greater for
higher V+ levels.
(Output): The output of the 555 comes from a high-current
totem-pole stage made up of transistors Q20 - Q24. Transistors Q21 and Q22
provide drive for source-type loads, and their Darlington connection provides a
high-state output voltage about 1.7 volts less than the V+ supply level used.
Transistor Q24 provides current-sinking capability for low-state loads referred
to V+ (such as typical TTL inputs). Transistor Q24 has a low saturation voltage,
which allows it to interface directly, with good noise margin, when driving
current-sinking logic. Exact output saturation levels vary markedly with supply
voltage, however, for both high and low states. At a V+ of 5 volts, for
instance, the low state Vce(sat) is typically 0.25 volts at 5 mA. Operating at
15 volts, however, it can sink 100mA if an output-low voltage level of 2 volts
is allowable (power dissipation should be considered in such a case, of course).
High-state level is typically 3.3 volts at V+ = 5 volts; 13.3 volts at V+ = 15
volts. Both the rise and fall times of the output waveform are quite fast,
typical switching times being 100nS.
The state of the output pin will always
reflect the inverse of the logic state of the latch, and this fact may be seen
by examining Fig. 3. Since the latch itself is not
directly accessible, this relationship may be best explained in terms of
latch-input trigger conditions. To trigger the output to a high condition, the
trigger input is momentarily taken from a higher to a lower level. [see "Pin 2 -
Trigger"]. This causes the latch to be set and the output to go high. Actuation
of the lower comparator is the only manner in which the output can be placed in
the high state. The output can be returned to a low state by causing the
threshold to go from a lower to a higher level [see "Pin 6 - Threshold"], which
resets the latch. The output can also be made to go low by taking the reset to a
low state near ground [see "Pin 4 - Reset"].
Pin 4 (Reset): This pin is also used to reset
the latch and return the ouput to a low state. The reset voltage threshold level
is 0.7 volt, and a sink current of 0.1mA from this pin is required to reset the
device. These levels are relatively independent of operating V+ level; thus the
reset input is TTL compatible for any supply voltage.
The reset input is an
overriding function; that is, it will force the output to a low state regardless
of the state of either of the other inputs. It may thus be used to terminate an
output pulse prematurely, to gate oscillations from "on" to "off", etc. Delay
time from reset to output is typically on the order of 0.5 uS, and the minumum
reset pulse width is 0.5 uS. Neither of these figures is guaranteed, however,
and may vary from one manufacturer to another. When not used, it is
recommended that the reset input be tied to V+ to avoid any possibility of false
Pin 5 (Control
Voltage): This pin allows direct access to the 2/3 V+
voltage-divider point, the reference level for the upper comparator. It also
allows indirect access to the lower comparator, as there is a 2:1 divider (R8 -
R9) from this point to the lower-comparator reference input, Q13. Use of this
terminal is the option of the user, but it does allow extreme flexibility by
permitting modification of the timing period, resetting of the comparator,
When the 555 timer is used in a voltage-controlled mode, its
voltage-controlled operation ranges from about 1 volt less than V+ down to
within 2 volts of ground (although this is not guaranteed). Voltages can be
safely applied outside these limits, but they should be confined within the
limits of V+ and ground for reliability.
In the event the control-voltage pin
is not used, it is recommended that it be bypassed with a capacitor of about
0.01uF (10nF) for immunity to noise, since it is a comparator
(Threshold): Pin 6 is one input to the upper comparator
(the other being pin 5) and is used to reset the latch, which causes the output
to go low.
Resetting via this terminal is accomplished by taking the terminal
from below to above a voltage level of 2/3 V+ (the normal voltage on pin 5). The
action of the threshold pin is level sensitive, allowing slow rate-of-change
The voltage range that can safely be applied to the threshold pin
is between V+ and ground. A dc current, termed the threshold current,
must also flow into this terminal from the external circuit. This current is
typically 100nA, and will define the upper limit of total resistance allowable
from pin 6 to V+. For either timing configuration operating at V+ = 5 volts,
this resistance is 16 Mega-ohm.
(Discharge): This pin is the open collector of an npn
transistor (Q14), the emitter of which goes to ground. The conduction state of
this transistor is identical in timing to that of the output stage. It is "on"
(low resistance to ground) when the output is low and "off" (high resistance to
ground) when the output is high.
In both the monostable and astable time
modes, this transistor switch is used to clamp the appropriate nodes of the
timing network to ground. Saturation voltage is typically below 100mV
(milli-Volt) for currents of 5 mA or less, and off-state leakage is about 20nA
(these parameters are not specified by all manufacturers, however).
collector current is internally limited by design, thereby removing restrictions
on capacitor size due to peak pulse-current discharge. In certain applications,
this open collector output can be used as an auxiliary output terminal, with
current-sinking capability similar to the output (pin 3).
Pin 8 (V +): The V+ pin (also
referred to as Vcc) is the positive supply voltage terminal of the 555 timer IC.
Supply-voltage operating range for the 555 is +4.5 volts (minimum) to +16 volts
(maximum), and it is specified for operation between +5 volts and + 15 volts.
The device will operate essentially the same over this range of voltages without
change in timing period. Actually, the most significant operational difference
is the output drive capability, which increases for both current and voltage
range as the supply voltage is increased. Sensitivity of time interval to supply
voltage change is low, typically 0.1% per volt.
Try the simple 555 testing-circuit of Fig. 5. to get you
going, and test all your 555 timer ic's. I build several for friends and family.
I bring my own tester to ham-fests and what not to instantly do a check and see
if they are oscillating. Or use as a trouble shooter in 555 based circuits. This
tester will quickly tell you if the timer is functional or not. Although not
foolproof, it will tell if the 555 is shorted or oscillating. If both Led's are
flashing the timer is most likely in good working order. If one or both Led's
are either off or on solid the timer is defective. Simple
The capacitor slows down as it charges, and in actual
fact never reaches the full supply voltage. That being the case, the maximum
charge it receives in the timing circuit (66.6% of the supply voltage) is a
little over the charge received after a time constant
The capacitor slows down as it discharges, and never
quite reaches the ground potential. That means the minimum voltage it operates
at must be greater than zero. Timing circuit is 63.2% of the supply
The discharge of a capacitor also takes time and we can
shorten the amount of time by decreasing resistance (R) to the flow of
Modes: The 555 timer has two basic operational modes: one shot and astable. In
the one-shot mode, the 555 acts like a monostable multivibrator. A monostable is
said to have a single stable state--that is the off state. Whenever it is
triggered by an input pulse, the monostable switches to its temporary state. It
remains in that state for a period of time determined by an RC network. It then
returns to its stable state. In other words, the monostable circuit generates a
single pulse of a fixed time duration each time it receives and input trigger
pulse. Thus the name one-shot. One-shot multivibrators are used for turning some
circuit or external component on or off for a specific length of time. It is
also used to generate delays. When multiple one-shots are cascaded, a variety of
sequential timing pulses can be generated. Those pulses will allow you to time
and sequence a number of related operations.
The other basic operational
mode of the 555 is as and astable multivibrator. An astable multivibrator is
simply and oscillator. The astable multivibrator generates a continuous stream
of rectangular off-on pulses that switch between two voltage levels. The
frequency of the pulses and their duty cycle are dependent upon the RC network
One-Shot Operation: Fig. 4 shows the basic circuit of the 555
connected as a monostable multivibrator. An external RC network is connected
between the supply voltage and ground. The junction of the resistor and
capacitor is connected to the threshold input which is the input to the upper
comparator. The internal discharge transistor is also connected to the junction
of the resistor and the capacitor. An input trigger pulse is applied to the
trigger input, which is the input to the lower comparator.
circuit configuration, the control flip-flop is initially reset. Therefore, the
output voltage is near zero volts. The signal from the control flip-flop causes
T1 to conduct and act as a short circuit across the external capacitor. For that
reason, the capacitor cannot charge. During that time, the input to the upper
comparator is near zero volts causing the comparator output to keep the control
Notice how the monostable continues to output its pulse
regardless of the inputs swing back up. That is because the output is only
triggered by the input pulse, the output actually depends on the capacitor
The 555 in fig. 9a is shown here in
it's utmost basic mode of operation; as a triggered monostable. One immediate
observation is the extreme simplicity of this circuit. Only two components to
make up a timer, a capacitor and a resistor. And for noise immunity maybe a
capacitor on pin 5. Due to the internal latching mechanism of the 555, the timer
will always time-out once triggered, regardless of any subsequent noise (such as
bounce) on the input trigger (pin 2). This is a great asset in interfacing the
555 with noisy sources. Just in case you don't know what 'bounce' is:
bounce is a type of fast, short term noise caused by a switch, relay, etc. and
then picked up by the input pin.
The trigger input is initially high (about
1/3 of +V). When a negative-going trigger pulse is applied to the trigger input
(see fig. 9a), the threshold on the lower comparator is exceeded. The lower
comparator, therefore, sets the flip-flop. That causes T1 to cut off, acting as
an open circuit. The setting of the flip-flop also causes a positive-going
output level which is the beginning of the output timing pulse.
capacitor now begins to charge through the external resistor. As soon as the
charge on the capacitor equal 2/3 of the supply voltage, the upper comparator
triggers and resets the control flip-flop. That terminates the output pulse
which switches back to zero. At this time, T1 again conducts thereby discharging
the capacitor. If a negative-going pulse is applied to the reset input while the
output pulse is high, it will be terminated immediately as that pulse will reset
Whenever a trigger pulse is applied to the input, the 555
will generate its single-duration output pulse. Depending upon the values of
external resistance and capacitance used, the output timing pulse may be
adjusted from approximately one millisecond to as high as on hundred seconds.
For time intervals less than approximately 1-millisecond, it is recommended that
standard logic one-shots designed for narrow pulses be used instead of a 555
timer. IC timers are normally used where long output pulses are required. In
this applicaton, the duration of the output pulse in seconds is approximately
T = 1.1 x R x C (in
The output pulse width is defined by the above
formula and with relatively few restrictions, timing components R(t) and C(t)
can have a wide range of values. There is actually no theoretical upper limit on
T (output pulse width), only practical ones. The lower limit is 10uS. You may
consider the range of T to be 10uS to infinity, bounded only by R and C limits.
Special R(t) and C(t) techniques allow for timing periods of days, weeks, and
even months if so desired.
However, a reasonable lower limit for R(t) is in
the order of about 10Kilo ohm, mainly from the standpoint of power economy.
(Although R(t) can be lower that 10K without harm, there is no need for this
from the standpoint of achieving a short pulse width.) A practical minimum for
C(t) is about 95pF; below this the stray effects of capacitance become
noticeable, limiting accuracy and predictability. Since it is obvious that the
product of these two minimums yields a T that is less the 10uS, there is much
flexibility in the selection of R(t) and C(t). Usually C(t) is selected first to
minimize size (and expense); then R(t) is chosen.
The upper limit for
R(t) is in the order of about 15 Mega ohm but should be less than this if all
the accuracy of which the 555 is capacle is to be achieved. The absolute upper
limit of R(t) is determined by the threshold current plus the discharge leakage
when the operating voltage is +5 volt. For example, with a threshold plus
leakage current of 120nA, this gives a maximum value of 14M for R(t) (very
optimistic value). Also, if the C(t) leakage current is such that the sum of the
threshold current and the leakage current is in excess of 120 nA the circuit
will never time-out because the upper threshold voltage will not be reached.
Therefore, it is good practice to select a value for R(t) so that, with a
voltage drop of 1/3 V+ across it, the value should be 100 times more, if
So, it should be obvious that the real limit to be placed on C(t)
is its leakage, not it's capacitance value, since larger-value capacitors have
higher leakages as a fact of life. Low-leakage types, like tantalum or NPO, are
available and preferred for long timing periods. Sometimes input trigger source
conditions can exist that will necessitate some type of signal conditioning to
ensure compatibility with the triggering requirements of the 555. This can be
achieved by adding another capacitor, one or two resistors and a small signal
diode to the input to form a pulse differentiator to shorten the input trigger
pulse to a width less than 10uS (in general, less than T). Their values and
criterion are not critical; the main one is that the width of the resulting
differentiated pulse (after C) should be less than the desired output
pulse for the period of time it is below the 1/3 V+ trigger level.
are several different types of 555 timers. The LM555 from National is the most
common one these days, in my opinion. The Exar XR-L555 timer is a micropower
version of the standard 555 offering a direct, pin-for-pin (also called
plug-compatible) substitute device with an advantage of a lower power operation.
It is capable of operation of a wider range of possitive supply voltage from as
low as 2.7volt minimum up to 18 volts maximum. At a supply voltage of +5V, the
L555 will typically dissipate of about 900 microwatts, making it ideally
suitable for battery operated circuits. The internal schematic of the L555 is
very much similar to the standard 555 but with additional features like 'current
spiking' filtering, lower output drive capability, higher nodal impedances, and
better noise reduction system.
Intersil's ICM7555 model is a low-power,
general purpose CMOS design version of the standard 555, also with a direct
pin-for-pin compatibility with the regular 555. It's advantages are very low
timing/bias currents, low power-dissipation operation and an even wider voltage
supply range of as low as 2.0 volts to 18 volts. At 5 volts the 7555 will
dissipate about 400 microwatts, making it also very suitable for battery
operation. The internal schematic of the 7555 (not shown) is however totally
different from the normal 555 version because of the different design process
with cmos technology. It has much higher input impedances than the standard
bipolar transistors used. The cmos version removes essentially any timing
component restraints related to timer bias currents, allowing resistances as
high as practical to be used.
This very versatile version should be
considered where a wide range of timing is desired, as well as low power
operation and low current sync'ing appears to be important in the particular
A couple years after Intersil, Texas Instruments came on the market
with another cmos variation called the LINCMOS (LINear CMOS) or Turbo 555. In
general, different manufacturers for the cmos 555's reduced the current from
10mA to 100µA while the supply voltage minimum was reduced to about 2 volts,
making it an ideal type for 3v applications. The cmos version is the choice for
battery powered circuits. However, the negative side for the cmos 555's is the
reduced output current, both for sync and source, but this problem can be solved
by adding a amplifier transistor on the output if so required. For comparison,
the regular 555 can easily deliver a 200mA output versus 5 to 50mA for the 7555.
On the workbench the regular 555 reached a limited output frequency of 180Khz
while the 7555 easily surpassed the 1.1Mhz mark and the TLC555 stopped at about
2.4Mhz. Components used were 1% Resistors and low-leakage capacitors, supply
voltage used was 10volt.
operation: Figure 9b shows the 555 connected as an astable multivibrator. Both
the trigger and threshold inputs (pins 2 and 6) to the two comparators are
connected together and to the external capacitor. The capacitor charges toward
the supply voltage through the two resistors, R1 and R2. The discharge pin (7)
connected to the internal transistor is connected to the junction of those two
When power is first applied to the circuit, the capacitor will
be uncharged, therefore, both the trigger and threshold inputs will be near zero
volts (see Fig. 10). The lower comparator sets the control flip-flop causing the
output to switch high. That also turns off transistor T1. That allows the
capacitor to begin charging through R1 and R2. As soon as the charge on the
capacitor reaches 2/3 of the supply voltage, the upper comparator will trigger
causing the flip-flop to reset. That causes the output to switch low. Transistor
T1 also conducts. The effect of T1 conducting causes resistor R2 to be connected
across the external capacitor. Resistor R2 is effectively connected to ground
through internal transistor T1. The result of that is that the capacitor now
begins to discharge through R2.
The only difference between the single
555, dual 556, and quad 558 (both 14-pin types), is the common power rail. For
the rest everything remains the same as the single version, 8-pin
As soon as the voltage
across the capacitor reaches 1/3 of the supply voltage, the lower comparator is
triggered. That again causes the control flip-flop to set and the output to go
high. Transistor T1 cuts off and again the capacitor begins to charge. That
cycle continues to repeat with the capacitor alternately charging and
discharging, as the comparators cause the flip-flop to be repeatedly set and
reset. The resulting output is a continuous stream of rectangular
The frequency of operation of the astable circuit is dependent
upon the values of R1, R2, and C. The frequency can be calculated with the
f = 1/(.693 x C x (R1 + 2 x
The Frequency f is in Hz, R1 and R2 are in ohms, and C
is in farads.
The time duration between pulses is known as the 'period', and
usually designated with a 't'. The pulse is on for t1 seconds, then off for t2
seconds. The total period (t) is t1 + t2 (see fig. 10).
That time interval is
related to the frequency by the familiar relationship:
f = 1/t
t = 1/f
intervals for the on and off portions of the ouput depend upon the values of R1
and R2. The ratio of the time duration when the ouput pulse is high to the total
period is known as the duty-cycle. The duty-cycle can be calculated with the
D = t1/t = (R1 + R2) / (R1 +
You can calculate t1 and t2 times with the formulas
t1 = .693(R1+R2)C
t2 = .693 x R2 x C
555, when connected as shown in Fig. 9b, can produce duty-cycles in the range of
approximately 55 to 95%. A duty-cycle of 80% means that the ouput pulse is on or
high for 80% of the total period. The duty-cycle can be adjusted by varying the
values of R1 and R2.
There are literally thousands of different
ways that the 555 can be used in electronic circuits. In almost every case,
however, the basic circuit is either a one-shot or an astable.
application usually requires a specific pulse time duration, operation
frequency, and duty-cycle. Additional components may have to be connected to the
555 to interface the device to external circuits or devices.
In the remainder
of this experiment, you will build both the one-shot and astable circuits and
learn about some of the different kinds of applications that can be implemented.
Furthermore, the last page of this document contains 555 examples which you can
build and experiment with.
In addition to a breadboard and a DC
powersupply with a voltage in the 5 to 12 volt range, you will need the
following components: 555 timer, LED, 2-inch /8 ohm loudspeaker, 150-ohm 1/4
watt resistor, two 10K ohm 1/4 resistors, two 1-Mega ohm 1/2 watt resistors, 10
Mega ohm 1/4 watt resistor, 0.1 uF capacitor, and a 0.68uF capacitor. All parts
are available from Radio Shack or Tandy.
This circuit is resetable by grounding pin 4,
so be sure to have an extra wire at pin 4 ready to test that
1. On your breadboard, wire the one-shot circuit as shown in figure 11.
2. Apply power to the circuit. If you have a standard 5 volt logic supply,
use it for convenience. You may use any voltage between 5 and 15
volts with a 555 timer. You can also run the circuit from battery power.
A standard 9-volt battery will work perfectly.
With the power connected, note the status of the LED:
is it on or off? ________________
3. Connect a short piece of hook-up wire to the trigger input line on pin 2.
Momentarily, touch that wire to ground. Remove it quickly. That will
create a pulse at the trigger input.
Note and record the state of LED: _____________________
4. Continue to observe the LED and note any change in the output state
after a period of time. What is the state? ______________
5. When you trigger the one-shot, time the duration of the output pulse with
a stopwatch or the seconds hand on your watch. To do that, the instant
that you trigger the one-shot by touching the wire to ground, immediately
start your stopwatch or make note of the seconds hand on your watch.
Trigger the one-shot and time the ouput pulse. Write in the approximate
value of the pulse-duration: ______________________
6. Using the values of external resistor and capacitor values in Fig. 11 and
the time interval formula for a one-shot, calculate the output-pulse duration.
What is your value? _____________________
7. Compare your calculated and timed values of output pulses. Explain any
discrepencies between your calculated and measured values.
8. Connect a short piece of hook-up wire to pin 4. You will use that as a
9. Trigger the one-shot as indicated previously. Then immediately thouch
the reset wire from pin 4 to ground. Note the LED result: _____________
10. With a DC voltmeter, measure the output voltage at pin 3 during the one
shot's off and on states. What are your values?
OFF: __________ volts ON: ___________ volts.
11. Replace the 10 MegOhm resistor with a 1 MegOhm resostor and repeat
steps 5 and 6. Record your timed and calculated results:
Timed: ________ seconds Calculated: _________seconds
If you want to get fancy, after you've completed the
experiment you can replace the resistors with potentiometers to build a variable
function generator and play with that to learn
12. Next you will experiment with astable circuits. First, rewire the circuit so
it appears as shown in Fig. 12.
13. Apply power to the circuit and observe the LED. What is happening?
14. Replace the 10 MegOhm resistor with a 1 MegOhm resistor. Again
observe the LED. Is the frequency higher or lower? _________________
15. Using the forumla given in the tutorial, calculate the oscillation frequency
using R1 as 10 MegOhm, and again with R1 as 1 MegOhm, and again with
R1 as 10 MegOhm. R2 is 1 MegOhm in both cases. Record your freq's:
f = _____________ Hz (R1 = 10 MegOhm)
f = _____________ Hz (R1 = 1 MegOhm)
16. Calculate the period, t1 and t2, and the duty-cycle for each resistor value:
10 MegOhm: t = ___________ t1 = ____________ t2 = ____________
1 MegOhm: t = ___________ t1 = ____________ t2= ____________
Monitoring the timer with a speaker can be
amusing if you switch capacitors or resistors to make an
17. Rewire the circuit making R1 and R2 10,000 ohms and C equal to 0.1uF.
Use the same circuit in Fig. 12. But, replace the LED and its resistor with
a speaker and capacitor as shown in Fig. 13.
18. Apply power to the circuit and note the result: ______________________
19. Calculate the frequency of the circuit: f = ____________________ Hz
20. If you have an oscilloscope, monitor the output voltage on pin 3.
Disconnect the speaker and note the output. Also, observe the capacitor
charge and discharge at pin 6 or 2: _____________________________
Review of steps 1 through 20:
circuit you built for those steps was a one-shot multi-vibrator. The circuit is
similar to that described in the tutorial. The trigger input is held high with a
10,000 ohm resistor. When you bring pin 2 low, by touching the wire to ground,
the one-shot is fired. The LED installed at the output of the 555 is used to
monitor the output pulse. The LED goes on when the one-shot is triggered.
component values selected for the circuit are large, so as to generate a long
output pulse. That allows you to measure the pulse duration with a stop watch.
Once the one-shot is triggered, the output LED stays on until the capacitor
charges to 2/3 of the supply voltage. That triggers the upper comparator and
causes the internal control flip-flop to reset, turning off the pulse and
discharging the capacitor. The one-shot will remain in that state until it is
Timing the pulse should have produced an output duration of
approximately 7.5 seconds. Calculating the output time interval using the
formula given previously, you found the pulse duration to be:
may have notice some difference between the calculated and actual measured
values. The differences probably result from inaccuracies in your timing.
Further, component tolerances may be such that the actual values are different
from the marked values.
In steps 8 and 9 you demonstrated the reset
function. As you saw, you could terminate the output pulse before the timing
cycle is completed by touching pin 4 to ground. That instantly resets the
flip-flop and shuts off the output pulse.
In step 10, you measured the
output voltage. When off, the output is only a fraction of a volt. For all
practical purposes it is zero. When triggered, the 555 generates a 3.5 volt
pulse with a 5-volt supply. If you used another value of supply voltage, you
would probably have discovered that the output during the pulse is about 1.5
volt less than the supply voltage.
In step11, you lowered the resistor
value to 1 Megohm. As you noticed, that greatly shortens the output pulse
duration. The LED only stayed on for a brief time; so brief in fact that you
probably couldn't time it accurately. The calculated duration of the output
pulse is 0.748 seconds.
The circuit you built for steps 12 - 20
was an astable multi-vibrator. The astable circuit is an oscillator whose
frequency is dependent upon the R1, R2, and C values. In step 13, you
should have found that the LED flashed off and on slowly.
frequency is 0.176 Hz. That gives a period of:
t = 1/f = 1/.176 = 5.66
Since R1 is larger than R2, the LED will be on
for a little over 5 seconds and it will stay off for only 0.5 seconds.
That translates to a duty-cycle of:
D = t1/t = 5.18/5.66 = .915 or
In step 14, you replaced the 10 MegOhm resistor
with a 1 MegOhm resistor making both R1 and R2 equal. The new frequency is 0.706
Hz, much higher than in step 13. That translates to a period of 1.41
seconds. Calculating the t1 and t2 times, you see that the LED is on for 0.942
second and off for 0.467 second. That represents a duty-cycle of:
D = 0.942/1.41 = 0.67 or
In step 17, you made R1 = R2 = 10,000 ohm (10K)
and C = 0.1uF. That increased the frequency to 480Hz. The result should have
been a loud tone in the speaker.
If you had used an oscilloscope, you saw the
output to be a distorted rectangular wave of about 2 volts peak-to-peak. That
distortion is caused by the speaker load. Removing it makes the waveform nice
and square and the voltage rises to about 5 volts peak-to-peak. The capacitor
waveform is a combination of the classical charge and discharge curves given
The time is useful in computer, function generators, clocks, music
synthesizers, games, flashing lights, printers, scanners and the list goes on
I have placed a couple of 555 circuit examples below for
your convenience. Play with different component values and use the formulas
mentioned earlier to calculate your results. Things to remember: For proper
monostable operation with the 555 timer, the negative-going trigger pulse width
should be kept short compared tot he desired output pulse width. Values for the
external timeing resistor and capacitor can either be determined from the
previous formulas. However, you should stay within the ranges of resistances
shown earlier to avoid the use of large value electrolytic capacitors, since
they tend to be leaky. Otherwise, tantalum or mylar types should be used. (For
noise immunity on most timer circuits I recommend a 0.01uF (10nF) ceramic
capacitor between pin 5 and ground.) In all circuit diagrams below I used the
LM555CN timer IC from National, but the NE555 and others should not give you any
Circuits 1 to 10:
Play with different indicating
devices such as bells, horns, lights, relays, or whatever (if possible). Try
different types of LDR's. If for any reason you get false triggering, connect a
ceramic 0.01uF (=10nF) capacitor between pin 5 (555) and ground. Keeping the
basic rules of the 555 timer, try different values for Ct and Rt (or the C &
R over pins 2, 6 & 7) Replace Rt with a 1 megohm potentiometer if you wish.
Make notes of the values used and use the formulas to calculate timing. Verify
your calculations with your timing.
Dark Detector: It will sound an alarm if it gets too dark all over
sudden. For example, this circuit could be used to notify when a lamp (or bulb)
burns out. The detector used is a regular cadmium-sulphide Light Dependent
Resistor or LDR, for short, to sense the absense of light and to
operate a small speaker. The LDR enables the alarm when light falls below a
Fig. 2, Power Alarm:
This circuit can be used as a audible 'Power-out Alarm'. It uses the
555 timer as an oscillator biased off by the presence of line-based DC voltage.
When the line voltage fails, the bias is removed, and the tone will be heard in
the speaker. R1 and C1 provide the DC bias that charges capacitor Ct to over 2/3
voltage, thereby holding the timer output low (as you learned previously). Diode
D1 provides DC bias to the timer-supply pin and, optionally, charges a
rechargeable 9-volt battery across D2. And when the line power fails, DC is
furnished to the timer through D2.
Tilt Switch: Actually really a alarm circuit, it shows how to use a
555 timer and a small glass-encapsulated mercury switch to indicate
The switch is mounted in its normal 'open' position, which allows the
timer output to stay low, as established by C1 on startup. When S1 is disturbed,
causing its contacts to be bridged by the mercury blob, the 555 latch is set to
a high output level where it will stay even if the switch is returned to its
starting position. The high output can be used to enable an alarm of the visual
or the audible type. Switch S2 will silent the alarm and reset the latch. C1 is
a ceramic 0.1uF (=100 nano-Farad) capacitor.
Fig. 4, Electric Eye Alarm: The Electric-Eye Alarm is
actually a simular circuit like the Dark Detector of Fig. 1. The same type of
LDR is used. The pitch for the speaker can be set with the 500 kilo-ohm
potentiometer. Watch for the orientation of the positive (+) of the 10uF
capacitor. The '+' goes to pin 3.
Metronome: A Metronome is a device used in the music industry. It
indicates the ritme by a 'toc-toc' sound which speed can be adjusted with the
250K potentiometer. Very handy if you learning to play music and need to keep
the correct ritme up.
Fig. 6, CW Practice
Oscillator: CW stands for 'Contineous Wave' or Morse-Code. You
can practice the morse-code with this circuit. The 100K potmeter is for the
'pitch' and the 10K for the speaker volume. The "Key" is a morse code
Fig. 7, CW Monitor: This
circuit monitors the morse code 'on-air' via the tuning circuit hookup to pin 4
and the short wire antenna. The 100K potmeter controls the
Fig. 8, Ten-Minute Timer:
Can be used as a time-out warning for Ham Radio. The Federal
Communications Commission (FCC) requires the ham radio operator to identify his
station by giving his call-sign at least every 10 minutes. This can be a
problem, especially during lengthy conversations when it is difficult to keep
track of time. The 555 is used as a one-shot so that a visual warning indicator
becomes active after 10-minutes. To begin the cycle, the reset switch is pressed
which causes the 'Green' led to light up. After 10 minutes, set by the
500K potentiometer R1, the 'Red' led will light to warn the operator that
he must indentify.
Fig. 9, Schmitt Trigger:
A very simple, but effective circuit. It cleans up any noisy input
signal in a nice, clean and square output signal. In radio control (R/C) it will
clean up noisy servo signals caused by rf interference by long servo leads. As
long as R1 equals R2, the 555 will automatically be biased for any supply
voltage in the 5 to 16 volt range. (Advanced Electronics: It should be noted
that there is a 180-degree phase shift.) This circuit also lends itself to
condition 60-Hz sine-wave reference signal taken from a 6.3 volt AC transformer
before driving a series of binary or divide-by-N counters. The major advantage
is that, unlike a conventional multivibrator type of squarer which devides the
input frequency by 2, this method simply squeares the 60-Hz sine wave reference
signal without division.
Fig. 10, Better
Timing: Better and more stable timing output is created with the
addition of a transistor and a diode to the R-C timing network. The frequency
can be varied over a wide range while maintaining a constant 50% duty-cycle.
When the output is high, the transistor is biased into saturation by R2
so that the charging current passes through the transistor and R1 to C. When the
output goes low, the discharge transistor (pin 7) cuts off the transistor
and discharges the capacitor through R1 and the diode. The high & low
periods are equal. The value of the capacitor (C) and the resistor (R1 or
potmeter) is not given. It is a mere example of how to do it and the values are
pending on the type of application, so choose your own values. The diode can be
any small signal diode like the NTE519, 1N4148, 1N914 or 1N3063, but a high
conductance Germanium or Schottky type for the diode will minimize the diode
voltage drops in the transistor and diode. However, the transistor should have a
high beta so that R2 can be large and still cause the transistor to saturate.
The transistor can be a TUN (europe), NTE123, 2N3569 and most others.
The following circuits are examples of how a 555 timer IC assist in
combination with another Integrated Circuit. Again, don't be
afraid to experiment. Unless you circumvent the min and max parameters of the
555, it is very hard to destroy. Just have fun and learn something doing
Circuits 11 to 14:
Play with different
indicating devices such as bells, horns, lights, relays, or whatever (if
possible). Try different types of LDR's. If for any reason you get false
triggering, connect a ceramic 0.01uF (=10nF) capacitor between pin 5 (555) and
ground. In all circuit diagrams below I used the LM555CN timer IC from National.
Keeping notes is an important aspect of the learning process.
Fig. 11, Two-Tones: The purpose of this
experiment is to wire two 555 timers together to create a 2-note tone. If you
wish, you can use the dual 556 timer ic.
Fig. 12, Recording Beep: This circuit is used to keep
recording of telephone conversations legal. As you may know, doing otherwise
without consent of the other party is illegal. The output of IC1 is fed to the
2nd 555's pin 3 and made audible via C2 and the speaker. Any 8-ohm speaker will
Fig. 13, Coin Toss:
Electronic 'Heads-or-tails' coin toss circuit. Basically a Yes
or No decision maker when you can't make up your mind yourself. The 555
is wired as a Astable Oscillator, driving in turn, via pin 3, the 7473 flip-flop.
When you press S1 it randomly selects the 'Heads' or 'Tails' led. The leds
flashrate is about 2Khz (kilo-Hertz), which is much faster than your eyes can
follow, so initially it appears that both leds are 'ON'. As soon as the switch
is released only one led will be lit.
14, Logic Probe: Provides you with three visible indicators; "Logic
1" (+, red led), "Logic 0" (-, green led), and "Pulse" (yellow led). Good for
TTL and CMOS. The yellow or 'pulse' led comes on for approximately 200 mSec to
indicate a pulse without regards to its width. This feature enables one to
observe a short-duration pulse that would otherwise not be seen on the logic 1
and 0 led's. A small switch (subminiature slide or momentary push) across the
20K resistor can be used to keep this "pulse" led on permanently after a pulse
In operation, for a logic 0 input signal, both the '0' led and the
pulse led will come 'ON', but the 'pulse' led will go off after 200 mSec. The
logic levels are detected via resistor R1 (1K), then amplified by T1 (NPN, Si-AF
Preamplifier/Driver), and selected by the 7400 IC for what they are. Diode D1 is
a small signal diode to protect the 7400 and the leds
from excessive inverse voltages during capacitor discharge.
For a logic '1'
input, only the logic '1' led (red) will be 'ON'. With the switch closed, the
circuit will indicate whether a negative-going or positive-going pulse has
occurred. If the pulse is positive-going, both the '0' and 'pulse' led's will be
on. If the pulse is negative-going, the '1' and 'pulse' led's will be
the listing in Table 2. It shows some variations in the 555 manufacturing
process by two different manufacturers, National Semiconductor and Signetics
Corporation. Since there are other manufacturers then those two I suggest when
you build a circuit to stick with the particular 555 model they specify in the
Unless you know what you're doing ofcourse...
The absolute maximum ratings (in free air) for NE/SA/SE types are:
Vcc, supply voltage: 18V
Input voltage (CONT, RESET, THRES, TRIG): Vcc
Output current: 225mA (approx)
Operating free-air temp. range: NE555........... 0°C - 70°C
SA555........... -40°C - 85°C
SE555, SE555C... -55°C - 125°C
Storage temperature range: -65°C - 150°C
Case temperature for 60sec. (FK package): 260°C
1. 555 Timer IC Circuits. Forrest
M. Mims III, Engineer's Mini Notebook. Radio Shack Cat. No: 62-5010.
& experiment with pulse generators, oscillators, and time delays."
IC Timer Cookbook. Walter G. Jung. Published by Howard W. Sams & Co., Inc.
"A reference 'must' for hobby, technicians, and
3. The 555 Timer Applications Sourcebook. Howard M. Berlin.
Published by Sams Inc. ISBN: 0-672-21538-1.
"Learn how to connect the 555,
perform 17 simple experiments."
Copyright © 1996 - 2000 by Tony van Roon
Docs updated, September 29, 2000